|
|
Product rating |
|
Voting |
|
|
|
|
|
|
Author: Matt Austin
I bought this block to make my case look cleaner from my RBX since it has the 3 barb and my temps dropped 2*. Im now running a FX51@2.4Ghz at 30* idle in the south so Im very happy.
|
Author: Andy
I used to have a Maze2 block on my Nforce2 board (which performed quite well). When I got my Athlon64 board I purchased the TDX to go with it. The build quality is amazing! The finish on the bottom was excellent - I had no need to lap the block. I'm g
|
Author: NoDestiny
I used the Maze4 before, it was OK. I re-did my setup with a high end pump and less tubing and this block, and on my A64 3000+, im getting 27* idle and 31* load! AWESOME BLOCK!
|
Author: Deefe.WoW.
Excellent block superb craftmanship. A++!!
|
Author: Brandon
Bought this to team up with my 3700+ and DFI lanparty UT NF3 250GB. This is an amazing block (moved up from a Koolance eXos system to a Danger Den system) Loving this sytem, My room is in the attic so Heat is extreme. Noticed instant temp drops. 5 St
|
Author: MsB
like the chrysler moto, If you can find a better cpu block, Buy It. But you can't, so dont bother.
|
Author: Thruster
very impressed with the quality and performance of this block. the hold down method leaves a lot to be desired though.
|
Author: Cameron
Base had an excellent shine on it. Dropped temps from 57C --> 43C, and the AS5 hasnt even cured yet. Slightly hard to get the thumbscrews onto the bolts, but once there on, its easy.
|
Author: Reuel
I want to get this block but what are Accelerator Nozzles? Why would I order them with this? **It's an accessory for people who like to tune there system. It isn't needed or required**
|
Author: jake
does this work on amd 64 X2???? **YES**
|
Author: Nick
Just got this baby installed running a 3.0e prescott at 3.45 and, only 7degrees over ambient. Will push further. 3.8 is the sweet spot
|
Author: eric
this block is amazing, get it now! i had a athlon 64 3000+ (2.0GHz) clocked at 2.9GHz and it idles at around 29*C. its so amazing. with the stock heatsink i would idle around 40*C at 2.4GHz. im also going to buy a maze4 gpu and chipset block, it will prolly increase my temps by a little bit, but not too much i hope. i have a Black Ice xflow 2 radiator, (2 120mm fans). and a d5 pump with fillport.
|
Author: osru
Hi everyone! I think your site is very interesting and useful. I always bookmarked it.
|
Author: Keith Swalin
Very impressed. My first water cooling set up, and all I can say is why didn't I do this along time ago?! This is no joke, 3800+X2 @ 69F idle state. No over clocks here, as my wife runs a voice studio, and I was after a silent PC. It will not stay at then temp for long when I start doing things, but I couldn't believe it when I saw it. Great job Danger Den!
|
Author: William H Stamper Jr
This is another excellent product from DD, mirror finish is a definite plus for those of you like me in search of the perfect thermal interface. I've been using the block for about 6 months on my 965BE clocked from 3.4 to 4.032 and with a 20c ambient she keeps my chip running @ 24c/32c idle/load. Highest temp on 8hrs of Prime95 was 36c. An absolute must-buy.
All above stats recorded with (1)Black Ice Pro III, DD-CPX-Pro Pump, w/ T-line, no res.
|
Add your review here |
|
|
